-G1: Linear move: E F S X Y Z
- G0: Linear move: E F S X Y Z
- G2: Draw lin arc: E F I J U X Y
- G3: Draw lin arc: E F I J U X Y
- G4: Dwell: P S
- G20: Set units to inches.
- G21: Set units to millimeters.
- G28: Move to origin: X Y Z
- G69: Random XY Killer: L Q S U V X Y
- G90: Set to absolute positioning.
- G91: Set to relative positioning.
- G92: Set position: E S X Y Z
- G100: Linear move: E F X Y Z
- G101: Relative linear move: E F X Y Z
- G102: Relative linear move width timeout: E F S T X Y Z
- G103: Clear timeout: S
- G104: Extrude width timeout: E T
- G195: Reset motion.
- G196: Reset all.
- G197: Pause.
- G198: Resume.
- G199: Imadiate pause.
- G194: Imadiate abort.
- M18: Disable stepper motors.
- M82: Set extruder to absolute mode.
- M83: Set extruder to relative mode.
- M84: Stop idle hold: S
- M8484: Motors off imadiate: S
- M105: Get temperature of extruders and bed: P T
- M106: Turn cooling fan on: S T
- M116: Turn cooling fan on: H L S T
- M104: Set extruder temperature: Q S T
- M109: Set and wait head temperature: Q S T
- M1400: Start heating and waiting: B E H P Q T
- M107: Turn cooling fan off.
- M110: Print Start or Stop: S
- M114: Get current position.
- M115: Get firmware version.
- M117: Display message.
- M140: Set bed temperature: H L S
- M190: Set and wait bed temperature: S
- M220: Set speed override percent: S
- M221: Set extrusion override percent: S
- M300: Play beep sound: P S
- M424: ...: E F
- M423: ...: E F T
- M422: Start Head Preparation.
- M425: Set nozzle wipe position: S
- M430: Head change ZHop settings: F Z
- M431: Head change Exit Retract settings: E F
- M432: Head change Enter Retract settings: E F
- M433: Head change Enter Prime settings: E F
- M450: Self test: E F
- M900: Linear advance beta version: A D K
- M905: Set feed High/Low: H L
- M73: M73 progressbar refresh: P S
- M1001: Get Printer Version.
- M1002: Get unique ID: S
- M1003: Get firmware version: S
- M1004: Get HMI version.
- M1005: Get HMI board version: S
- M1006: Set limits s=1 Case / S=2 Head: H L S T
- M1014: Get ADC values: S
- M1015: Get PWM duty.
- M1020: Puffer mode: S
- M1104: Get Info: P
- M1105: Get HMI mode.
- M1106: Set HMI mode.
- M1114: Get machine coordinates.
- M1115: Get queue.
- M1116: Set Min Q: Q
- M1123: Set T7 pin high or low: S
- M1160: Fan control (Case,Dome,Head,Obj): C D H O T
- M1161: Fan override: S
- M1200: Set feed properties: F H L
- M1202: Set axis soft limit: E X Y Z
- M1203: Set XY acceleration: A D F
- M1204: Set Z acceleration: A D F
- M1210: Set extruder correction: F K
- M1211: Set extruder correction: F K
- M1212: Set thermal runaway: Q S
- M1297: Mem dump: S
- M1298: Send command: S
- M1299: Queue report: S
- M1300: Set extruders PID: D F I P W
- M1301: Set bed PID: D F I P W
- M1401: Seat head heating curve: D Q
- M1402: Seat bed heating curve: D Q
- M1403: Flush.
- M1800: Set HMI Baud: S
- M1885: Set G1 counter: S
- M1886: Read restart data.
- M1887: Read startup GPBR.
- M1888: Backup: Q S
- M1889: Set RTC: D S
- M2001: Set max imp: E X Y Z
- M2002: Set ref imp: X Z
- M2003: Soft Enable encoder: S
- M2004: Enable encoder check: S
- M2005: Set encoder div: Q S
- M2006: Set encoder calibstate: S
- M2007: Encoder autoset: S
- M2008: Set encoder params: Q S
- M3000: Get X Y Z jupers states: J X Y Z
- M3001: Set LED strip brightness: L
- M3002: Set LCD backlight brightness: L
- M4001: Set heating overlap: P
- M4003: Set maximum head heat temp: H S
- M4004: Get heat state: S
- M4005: Set maximum bed heat temp: H S
- M5000: Set XY Z jog feed: X Z
- M5001: Set mechanical parameters: E X Z
- M5002: Set XY offset: X Y
- M5003: Set TMC2130 current: E X Y Z
- M5004: Get TMC2130 status regiter.
- M5005: XY calibration moode: S
- M6666: Reset: S
- M6969: Erase flash: S
- M7001: Set WIFI SSID/Pass.
- M7002: Wifi List AP First.
- M7003: HMI send WIFI AP list.
- M7004: WiFi Report: Q S T
- M7005: Set e-mail address.
- M7006: Get AT version number.
- M7007: Rec WiFi AT version.
- M7008: Overwrite Wi-Fi SSID.
- M7009: wifi reset pin check: S
- M8001: Read motor: Q S
- M8010: Read errors.
- M8020: Set thermal motor warning: S
- M9001: Set LED to function.
- M9003: ReadMotorDIAG.
- M9005: Enable/disable cover: S
- M9006: Set print mode: Q S X
- M9007: Switch off calculation.
- M9008: Set nozzle diameter: D T
- M9090: Set parser limits: S X Y Z
- M9999: Set MicroStep: E X Y Z
- M765: calc offset.
- M766: Meas x y distance: D T
- T0: Select tool 1: F S X Y Z
- T1: Select tool 2: F S X Y Z
Comments
0 comments
Please sign in to leave a comment.